Outer frame


Most CoreXY have a square outer frame, and I am using the HEVO design. I am using the 300x300x300 design from the configurator but with an extra height of 100mm, so I can keep the electronics at the bottom. My plan is to use a thick MDF plate at the bottom, both for mounting the electronics and for adding weight and rigidity to the frame. Also, I will lower the top front bar, just to get a different look (an idea I got from somewhere I forgot).

The precise measures of the 3030 extrusions are made to fit a 300x300mm build plate with the standard mounting parts. I will probably not use the standard parts, but will just choose or design parts so the fit with the standard frame and build plate. This fixes at least some variables, and allowed me to get an (almost) standard frame kit.

more info will come here as I start the actual build...

Comments

Post a Comment

Popular posts from this blog

Electronics #3: Setting up the first RAMPS with Klipper

Image
This is part #3 in a list of postings on the electronics of my CEVO. The full list can be found  here . The topic of this list is initial very simple setup of a RAMPS/Arduino with Klipper. Note that further steps comes in later parts and that the photographs shows my test setup, not the final wiring. When talking about the RAMPS board, we usually means the RAMPS 1.4  , which is a quite simple board that is designed to piggyback on an Arduino Mega . Originally is was designed as an 12V board, but most boards can be used more or less directly with 24V following one of the many guides on doing this (see for example here and here ). The original design was made for manual soldering, and most RAMPS boards are variations of varying quality of this, I am however going for the BIGTREETECH Ramps 1.6 , which is a Chinese surface mount design - see a good review here , also read the enlightening comments below the video. I have two of these, and to my unqualified eyes they look to have quite
Read more

Electronics #2: Setting up Raspberry Pi with OctoPrint

Image
This is part #2 in a list of postings on the electronics of my CEVO. The full list can be found  here . The topic of this list is setting up a Raspberry Pi with OctoPrint. Note that installation of Klipper comes in part #3 and that the photographs shows my test setup, not the final wiring. I am using an Pi 3B, that I already had. While the speed of the Arduino does not matter that much, the speed of the Pi does. This is where I will run OctoPrint, Klipper, camera, interesting plugins and other stuff, so the faster the merrier. If I was buying new I might go for an upper end Orange Pi or at least an Pi 3B+. The Pi and the Arduinoes does not need more than 2A, even if they also power some sensors, fans, and the like. I am however using an 5V 7A power supply I had lying around. I am powering the Pi through the GPIO pins 2 and 6 - that is fine in a configuration like this and with any fairly decent power supply. Installation of OctoPrint is very simple by just following the stand
Read more

Electronics #?: wiring a stepper motor

Image
This is part #? in a list of postings on the electronics of my CEVO. The full list can be found  here . The topic of this post is how to wire the stepper motor to the RAMPS. I am pretty sure most newer motors are the same, and yet I had difficulties to find a simple guide on how to do the wiring. The most referenced guide is  https://reprap.org/wiki/Stepper_wiring , and that was indeed the generic guide I used as reference. I am however quite sure you can just follow my guide below. Most DIY 3D printer uses Nema17 stepper motors like the one on the right. The one in the picture uses a 6-pin connector, a JST 2.0 PH 6-pin male connector, and that seems to be pretty much standard. This connector is generally not that common, but you can order it for example at  Aliexpress . Even though it has 6 pins, it is actually a bipolar motor with only 4 connectors, as shown in the diagram on the right. To wire the motor we need to know the wires for the A coil and for the B coil. If in dou
Read more